Cabinets based on a 19" support structure system. As standard, ST standing cabinets are manufactured in two height options 42U and 24U and three depth options 600, 800, 1000 mm. Cabinets are sold pre-assembled and for self-assembly - this design allows easy transport and assembly in hard-to-reach places. We also offer single-section SW and two-section SWD wall cabinets in heights of 6U, 10U, 15U, 18U. We also manufacture additional equipment for cabinets . plinths, ventilation panels, fixed and pull-out shelves, etc.
Products
Cabinets
Cabinets are based on a system of 19" support structures. As a standard, ST standing cabinets are manufactured in two height options: 42U and 24U and in three depths: 600, 800, 1000 mm. We sell cabinets in an assembled version and for self-assembly - this construction enables easy transport and assembly in places which are difficult to access. We also offer single-section SW and double-section SWD wall cabinets in heights of 6U, 10U, 15U, 18U. We also manufacture additional equipment for cabinets . plinths, ventilation panels, fixed and pull-out shelves, etc.
Products
The cabinet is designed for mounting devices based on the 19" support structure system, cassettes with packages and plates, ventilation panels, etc. It provides the possibility of mounting ancillary equipment with the use of additional equipment such as: shelves, slides, brackets, etc. The cabinet is powder-coated to provide a durable protective coating and an aesthetically pleasing appearance. The bolted construction allows easy transport and installation in places that are difficult to access. Cabinets are manufactured as standard in two height options: 42U and 24U.
Applied services:
-
CNC punching
-
Bending
-
Metal welding
-
Welding
Wall cabinets with glass front doors are intended for installation in small offices and installations with low saturation of subscriber outlets, e.g. warehouses, production halls, etc. The cabinet is of split construction, i.e. after attaching the rear section to the wall, it is possible to open the front section for easy access to the inside of the cabinet and the equipment installed in it. The cabinet has four cable entry openings with metal plugs, two in the back wall, and one in each of the floor and ceiling. The cabinet has two ventilation openings protected by perforated mesh. One of these is pre-shuttered with a filter cap. A ventilation panel (with or without thermostat) with two fans mounted to the roof of the cabinet in place of the perforations is available. The cabinet is made of 1,25 mm thick steel sheet. The cabinets are available in the following configurations 6U, 10U, 15U and 18U. The width of the cabinet is 583mm and the depth is 525mm measured from the outer contour The usable depth measured from the front frame in its maximum position to the rear wall is 480mm.
Applied services:
-
CNC punching
-
Bending
-
Metal welding
-
Welding
Cabinet-mounted plinths allow cables to be inserted from either side.
The structure is powder-coated to provide a durable protective coating and an aesthetically pleasing appearance.
Plinths are supplied in a standard height of 120mm.
Applied services:
-
CNC punching
-
Bending
-
Metal welding
-
Welding
Ventilation panels force air exchange in the enclosure.
The panels are manufactured in two versions :
- 2 fan 2W
- 4-fan 4W
Each panel can be fitted with a thermostat to switch on the fans if the set temperature inside the enclosure is exceeded.
Applied services:
-
CNC punching
-
Bending
-
Metal welding
-
Welding
Pull-out shelves are fitted to the mounting rails.
They allow the location of equipment that requires constant servicing or adjustment.
The structure is powder-coated for a durable protective coating and aesthetically pleasing appearance.
Applied services:
-
CNC punching
-
Bending
-
Metal welding
-
Welding
The filter plug installed in the enclosure floor protects the interior of the enclosure from dust being drawn into the construction The construction is powder-coated for a durable protective coating and an aesthetically pleasing appearance. The insert is a filtering fleece.
Mounting slats made of 1,5 mm thick AlZn sheet allow mounting 19" accessories with the use of self-locking cage nuts M6 KLIPKO. The design of the enclosure's brackets makes it possible to adjust the mounting of the slats.
Applied services:
-
CNC punching
-
Bending
-
Metal welding
-
Welding